10 ft Tools site container
Time is Money, and when diving equipment goes down on a job, it’s not just the cost for the delays to the diving company, nearly always the entire site is affected by these delays. To mitigate downtime, and as part of our emergency preparedness MMC Diving Services plan for the worst case or what if’s.
MMC Custom designed 10ft containerized site tools container or workshop / stores is fully kitted out with bench mounted tools, vice and a full inventory of hand tools and spares for almost every foreseen eventuality, 110 and 240v power point sockets, inside and outside lighting which has been certified under the fixed electrical compliance check.Our container is sent to site following a dynamic site-specific risk assessment, loaded with spares relevant to the foreseeable needs of the site, eg; Helmet, panel, underwater camera and lighting equipment, welding and burning equipment spares, hydraulics, etc.
Certification:
- Certification Number: GB/C 9274 BV/2010
- Type: RXTC-10ITX
- Manufacture: 8 2014
- Identification NO: RX1409333
- Approx. weight with equipment: 2.5 Tonne
The outside length is 3m / 9ft 10in, while the internal height is 2.39m / 7ft 10in. The outside height is 2.6m / 8ft 6in and the internal width is 2.35m / 7ft 8in. The outside width is 2.44m / 8ft and the door width is 2.34m / 7ft 8in.
The height of the door is usually 2.28m / 7ft 5in. The internal length is 2.84m / 9ft 3in.
The general specifications are as follows: the tare weight is 1,300kg / 2,870lbs. and the maximum gross weight is 10,160kg / 22,400lbs. The cubic capacity is 15.1 cubic meters / 561 cubic feet. These structures have steel doors. The frame and sides are all constructed from steel.
Tools and equipment specification:
- Combination Spanner 6-50mm
- Screwdriver Set
- Grinder 4½" 110v
- Grinder 9" 110v
- Grinder Spanner
- Grinding discs box of 4½"
- Grinding discs box of 9"
- Adjustable wrench 150mm
- Adjustable wrench 200mm
- Adjustable wrench 250mm
- Crow foot wrench 3/4" 10mm-18mm
- Club hammer 4lb
- Digital Calipers
- Underwater calipers (plastic)
- Drill Set 1-13mm
- Gloves disposable Latex XL (100 per Box)
- Tape Measure
- Non Conforming tags
- Letter/number punch set
- Stainley blades
- Torque Wrench
- First aid kit (MMC 001 FAK) 10 Man
- Cat c kit offshore medical kit (MMC 008 FAK)
- Defibrillator (MMC 003 DEF)
- Eye wash
- Splint
- Ice Pack
- Incident Response Plan
- Burns kit
- Eye wash station
- Emergency o2- mask
- Spinal board (MMC 001 SPB)
- Bench grinder 6" (MMC 001 BGR)
- Ultrasonic Bath
- Vice 6"
- Chain saw bench sharpner
- Pillar Drill (MMC 001 PDR)
- Grease gun
- Tape measure 30m
- Tape measure 50m
- Funnel set
- Clamps
- Large magnet
- Installation tester
- Multimeter Digital
- Jubilee clips
- Cable ties
- Whip checks
- Visor
- Welding rods 3/2 box
- Welding leads
- Wire brush
- Chipping hammer
- 240v Grinder
- Torch
- Bolster chisel
- Gloves rubber
- Sparkers
Tools and equipment:
- Cylinder keys
- Quivers
- Pick hammers
- Gloves welding
- Pelding mask
- Burning goggles
- Spanner 30mm
- Spanner 32mm
- Spanner 33mm
- Spanner 35mm
- Spanner 36mm
- Spanner 38mm
- Spanner 41mm
- Spanner 42mm
- Spanner 44mm
- Spanner 46mm
- Spanner 48mm
- Spanner 50mm
- Spanner 75mm
- Spanner 5/8" - 1/18 Ring
- Spanner 7/8W
- Ring spanner stainless steel custom
- Spanner 7/8W - BS
- Filter wrench
- Spanner open ended 1 1/8" W
- Spanner open ended 46-50mm
- Spanner Open Ended 65mm
- Ring spanner 1" 7/8 - 1/8
- Spanner ring 1"
- Spanner 1 1/8 BS - 1" W double ended
- Box of Gloves, Dust masks, Ear plugs, Safety goggles
- Brocco 3/8 burning rod box
- MMC 001 ACS Stihl TS410 3.2-kW cut-off saw (300mm/12" cutting wheel)
- Chain drive
- Socket Set 1" square drive
- Socket set 3/4" square drive
- Scoket set 1/2 square drive
- Wrench sube
- Burning/welding box (peli case)
- Earth clamps
- Regulators
- Stingers
- Quivers
- Spares box
- Burning goggles
- Cylinder keys
- Burning spares
- Inspection camera
- Impact gun
- Heater
- Inverter welder
- Fittings (small peli)
- 110v generator (MMC 004 GEN)
- 240v generator (MMC 006 GEN)
- Broom
- Dustpan & brush
- Sledge hammer
- Drill ( dewalt)
- 110v transformer box
- 110v extension lead
- Extension lead
- Pull Kit 10tonne Hydraulic
- Hose 25m
- Wire cutters
- Tap
- Barnacle scraper
- Measuring staff
- Cylinder bank
- 10 Tonne porta power
Tools and equipment added for jobs:
- Spare C-vision system (MMC 002 CTN)
- Accessories box C-vision.
- PELI case (spares) full Kirby helmet spares, panel, gauges, hoses, gas fittings etc.
- MMC 047 CYL and MMC 048 CYL 500 Litre Cylinders
- Spare Bell Jackets (MMC 009 BEL MMC 010 BEL)
- 12 litre cylinders (MMC 009 CYL - MMC 010 CYL)
- MMC 001 UMB, MMC 002 UMB, MMC 011 UMB 125m Umbilical’s
- Spare LP compressor 4 (MMC 004 CLP)
- Spare A flag
- Alcohol & Drug test kit.
